I miss the shuttle launch tower

[Raffaele]

hi mates!

I'm spending the night to re-install orbiter

BUT!

after installing Shuttle Fleet v 4[1].0.1 and then hi res KSC
i cant see the launch tower for the shuttle at KSC
I tryied to install Hi res LC39 too but nothing seems to work

searching in the forum, seems that I can't find any solution, that's why i'm posting this new thread

thanks to all

oh I tryied also to install this patch... is for shuttle fleet v.3 but nothing happen http://orbithangar.com/searchid.php?ID=2965

 

[The Aviator]

Ciao e benvenuto su Orbiter Forum!!!
Translation for non-italian talkers: Hi and welcome on Orbiter Forum!!!
You can try to copy the tower data from a scenario that have them and paste in the scenario without...
Or you can use the excellent Pad 39 B of Kev 33 that you can manage and put into a scenario like a vessel. You can find it on Orbit Hangar. If you have other doubts, count on me, mate!

 

[xmariox]

hi mates!

I'm spending the night to re-install orbiter

BUT!

after installing Shuttle Fleet v 4[1].0.1 and then hi res KSC
i cant see the launch tower for the shuttle at KSC
I tryied to install Hi res LC39 too but nothing seems to work

searching in the forum, seems that I can't find any solution, that's why i'm posting this new thread

thanks to all

oh I tryied also to install this patch... is for shuttle fleet v.3 but nothing happen http://orbithangar.com/searchid.php?ID=2965

You need also STS-Expansion Pack 4.0.1 where are included Pads
[ame="http://www.orbithangar.com/searchid.php?ID=3219"]Search[/ame]

 

[The Aviator]

You need also STS-Expansion Pack 4.0.1 where are included Pads

I used it for months without exp pack, and I had pads in the right place. Maybe I'm magic? :lol:

 

[xmariox]

Oh sorry I didn´t understand what he meant...

 

[Raffaele]

oè!!!!!!! :beach:

thanks a lot mate! I'm tying to install the hi res for KSC from kev 33
I'll let you know... i a few minutes (i hope)

ciao!


-----Posted Added-----


using kev33 textures seems that tower complex ant the roads are not alligned with the surface textures... maybe cause i'm using lev10 earth....
and to be honest i found thet the texures from the KSC kukatonas are much better than these ones...

my question is.... hi res KSC and Shuttle and shuttle fleet v.4.1 are in the recommended add on of the forum, but seems that no one has experienced this problem.....

I'm going to refresh the install process at all....

 

[The Aviator]

I don't know if Level 10 Earth can be the cause of this problem.
Tomorrow I will make some tests. If addons combinations won't work, maybe you'll have to manually change the positions of pads. If you succeed resolving this problem, post here, and if you won't succeed, even post here!
I'm happy to see I'm not the only Italian here.

 

[Raffaele]

thanks a lot!
I think I'll need some help to edit the pads position.... i'll offer you a beer if you come around in tuscany!

 

[The Aviator]

i'll offer you a beer if you come around in tuscany!

And I will offer you a "cassata" if you come here down in Sicily! :lol:
Good (orbiting) night!

 

[Orbinaut Pete]

Ok, i had this same problem (i have just installed shutte fleet).

The roads will not line up as they were not intended for Hi-res KSC, you will have to remove them from your config.

Go to config and delete the following completely:

K-v9-Sol
K-v9-Earth (folder AND file)

Then put this into any scenario you want: (i have changes pos)

K-LC-39B-v9:Spacecraft\Spacecraft2
STATUS Landed Earth
POS -80.6203280 28.6267950
HEADING 0.00
NAVFREQ 94 481
CONFIGURATION 1
CURRENT_PAYLOAD 0
END
K-LC-39-v9-FC:Spacecraft\Spacecraft2
STATUS Landed Earth
POS -80.6041800 28.6085240
HEADING 53.44
NAVFREQ 94 481
CONFIGURATION 1
CURRENT_PAYLOAD 0
SEQ 0 -2 0.006499
END
K-LC-39-v9-GW:Spacecraft\Spacecraft2
STATUS Landed Earth
POS -80.6042080 28.6084340
HEADING 355.53
NAVFREQ 94 481
CONFIGURATION 1
CURRENT_PAYLOAD 0
SEQ 0 -2 0.016800
END
K-LC-39-v9-RSS:Spacecraft\Spacecraft2
STATUS Landed Earth
POS -80.6044400 28.6082540
HEADING 359.72
NAVFREQ 94 481
CONFIGURATION 1
CURRENT_PAYLOAD 0
SEQ 0 -2 0.000000
END
K-LC-39A-v9:Spacecraft\Spacecraft2
STATUS Landed Earth
POS -80.6035600 28.6079540
HEADING 0.56
NAVFREQ 94 481
CONFIGURATION 1
CURRENT_PAYLOAD 0
END
K-LC-39-v9-Sparks1:Spacecraft\Spacecraft2
STATUS Landed Earth
POS -80.603994 28.608420
HEADING 88.228277
PRPLEVEL 0:1.000
THLEVEL 0:1.000
CONFIGURATION 1
CURRENT_PAYLOAD 0
END
K-LC-39-v9-Sparks2:Spacecraft\Spacecraft2
STATUS Landed Earth
POS -80.604106 28.608420
HEADING 266.314065
PRPLEVEL 0:1.000
THLEVEL 0:1.000
CONFIGURATION 1
CURRENT_PAYLOAD 0
END
K-LC-39-v9-Add:Spacecraft\Spacecraft2
STATUS Landed Earth
POS -80.6043400 28.6083940
HEADING 0.56
NAVFREQ 94 481
CONFIGURATION 1
CURRENT_PAYLOAD 0
END

Then, change pos of shuttle to this:

STATUS Landed Earth
BASE Cape Canaveral:1
POS -80.6040500 28.6084640
HEADING 0.56

Make sure that the system is just "Sol", not "K-v9-Sol" (At top of scn file).

Thats it!

Happy Orbiting!

 

[Raffaele]

thanks a LOT pete!

i'll try and let you know!

 

[The Aviator]

If you want a very good and realistic launchpad try LC39-EAFB 2006.3. You can find a low res launchpad on Orbit Hangar, but there is a link at the author site where you can download the hi res scenario. Try this on another Orbiter installation. First install Hi-res KSC by Kukanotas and then LC39-AFB 2006.3. I mean it's the best launchpad for the shuttle. For now.